Lighting
Eltako
grimmpp/home-assistant-eltako · vv1.5.10-bugfix-covers
HACSLocal push
Integration for Eltako 14 series in Home Assistant
In Apple Home through HomeKit Bridge
What HomeKit Bridge makes of each kind of entity this integration creates, read from its source code. A device only gets the ones that apply to it.
| Entity | Shows up as | Note |
|---|---|---|
light | Light | |
switch | Switch or outlet | |
cover | Blind, garage door, window or door | |
climate | Thermostat | |
binary_sensor | Sensor (motion, contact, leak, smoke…) | |
sensor | Sensor (temperature, humidity, air quality…) | |
button | Button (as a switch) | |
select | Mode picker (as switches) |
What people report
Local EnOcean/Eltako bus support for many actuators and sensors, but wireless FL62/FJ62 actuators and PioTek MGW-LAN sending have problems.
- Works4
- Not working3
- Requested1
| Device | In Home Assistant | In Apple Home | What they said | Source |
|---|---|---|---|---|
| Eltako FSR14 relay actuator | Works Local | Main supported actuator familySaved copyHi their, first of all many thanks to all your great work! I mainly use our tool to control my FSR14 devices ... in order to get rid of my bad little Homee device with the enocean add-on I would like to control al of my FL62 actors with your add-on. I can already see the status change of the FL62-actor. I´m going to set the actor in learning mode (by 4 short and 1 long push of the local button) 2024-11-10 17:34:13.952 DEBUG (Thread-4) [eltako] [Gateway] [Id: 1] Received message: 2024-11-10 17:34:13.997 DEBUG (Thread-2) [eltako] [Gateway] [Id: 2] Received message: 2024-11-10 17:34:16.202 DEBUG … Excerpt saved from GitHub on 2026-10-23. | Issue #135 · 2024-11 | |
| Eltako FSR61 / FSR62 actuators | Works Local | Owner tested teach-in and telegrams on FSR61; FSR62 expected sameSaved copy… the FL62-actor. I´m going to set the actor in learning mode (by 4 short and 1 long push of the local button) 2024-11-10 17:34:13.952 DEBUG (Thread-4) [eltako] [Gateway] [Id: 1] Received message: 2024-11-10 17:34:13.997 DEBUG (Thread-2) [eltako] [Gateway] [Id: 2] Received message: 2024-11-10 17:34:16.202 DEBUG (Thread-4) [eltako] [Gateway] [Id: 1] Received message: 2024-11-10 17:34:16.248 DEBUG (Thread-2) [eltako] [Gateway] [Id: 2] Received message: But I´ve been running into several problems: Seems like the teach in Button don't work. 2024-11-10 17:34:18.815 WARNING (Thread-2) … Excerpt saved from GitHub on 2026-10-23. | Issue #135 · 2024-11 | |
| Eltako FST14EM | Works Local | Binary sensor support addedSaved copyThe original text was already deleted or overwritten when we archived it. | PR #48 · 2024-01 | |
| Eltako heating/cooling actors FAE14, FHK14, F4HK14, F2L14, FHK61, FME14 | Works Local | Climate panel added in v1.1.0Saved copyversion 1.1.0 - Heating and Cooling * Change file introduced * Climate Panel introduced incl. support for actors like FAE14, FHK14, F4HK14, F2L14, FHK61, FME14 and EEP A5-10-06 as well as control panels like FTAF55ED. * Docs for Climate Panel/Heating and Cooling * Refactoring * Introduced many explicit types. * Logging improved * Prepared config for other gateway types. (Currently supported Eltako fam14 and fgw14-usb) * Support of different gateways e.g. enOcean USB300 with different protocol version (ESP3) * Added teach-in buttons for climate and temperature controller * Added Air Quality … Excerpt saved from GitHub on 2026-10-23. | PR #4 · 2023-11 | |
| Eltako FJ62NP-230V covers | Not working Local | Teach-in via mgw-lan fails; a user soft-fork made it workSaved copy… you make any progress on this? I have a very similar problem with these "Cannot convert to esp2 message" messages in the log after trying to teach in FJ62NP-230V based covers via mgw-lan. Excerpt saved from GitHub on 2026-10-23. | Issue #135 · 2024-11 | |
| Eltako FL62 actors | Not working Local | Status updates seen but teach-in fails with ESP2 conversion errorsSaved copy… use our tool to control my FSR14 devices ... in order to get rid of my bad little Homee device with the enocean add-on I would like to control al of my FL62 actors with your add-on. I can already see the status change of the FL62-actor. I´m going to set the actor in learning mode (by 4 short and 1 long push of the local button) 2024-11-10 17:34:13.952 DEBUG (Thread-4) [eltako] [Gateway] [Id: 1] Received message: 2024-11-10 17:34:13.997 DEBUG (Thread-2) [eltako] [Gateway] [Id: 2] Received message: 2024-11-10 17:34:16.202 DEBUG (Thread-4) [eltako] [Gateway] [Id: 1] Received message: 2024-11-10 … Excerpt saved from GitHub on 2026-10-23. | Issue #135 · 2024-11 | |
| PioTek MGW-ETH gateway | Not working Local | Receiving works; sending fails 'Cannot convert to esp2 message' on Python 3.14Saved copyGateway: PioTek MGW-ETH (device_type: mgw-lan, ESP3 over TCP) Integration: v1.5.10-bugfix-covers · Python: 3.14 Receiving works fine – actuator feedback (FF-A6-7A-A9/AA, 4BS) is decoded correctly and cover state updates. Sending does not work: every outgoing command is followed by Cannot convert to esp2 message (0x02 ...) in eltakobus.tcp2serial, and the actuator does not react. There is also a blocking-call traceback in esp3_tcp_com.py while loading EEP.xml, and a ValueError: incorrect unit of measurement: Messages when adding a gateway sensor. Looks like an ESP3-send / Python 3.14 … Excerpt saved from GitHub on 2026-10-23. | Issue #204 · 2026-07 | |
| PioTek TF-TTB tracker (A5-07-01) | Requested Local | Decentralized devices like A5-07-01, F6-05-02, A5-38-08 not working for userSaved copy… transferring all my devices to this integration. While the FGW14-USB works like a charm, I am struggling with my decentralized devices such as: 1. Eltako PioTek TF-TTB Funk Taster Tracker EEP Profile A5-07-01 https://www.piotek.de/FTTB?srsltid=AfmBOoo9OVYuwXAELEG5f4hOeEp7vwAG5Qtau4MtQjBTuizwFI6UgdWl 3. AFRISO ASD 20 Smoke Detector EEP Profile F6-05-https://res.cloudinary.com/afriso/image/upload/fl_attachment:dok_tec_ban_900_000_0801/78569.pdf 4. Eltako FSR71-2x-230V EEP Profile A5-38-08 (01) 5. Eltako FSR61NP EEP Profile A5-38-08 (01) I would love to help implement this EEP's and contribute … Excerpt saved from GitHub on 2026-10-23. | Issue #192 · 2026-04 |
Gathered from GitHub issues, pull requests, discussions and docs, and from r/homeassistant. These are individual reports, so check the linked thread and the date before you buy.
How it connects
Local push
Talks to the device on your network, and the device tells Home Assistant the moment something changes.
Details
| Installs (analytics) | 130 (0.02%) |
|---|---|
| GitHub stars | 77 |
| Latest version | v1.5.10-bugfix-covers (2026-08-28) |
| Set up in the UI | Yes |
| Maintainers | @grimmpp |
| License | MIT |
In ReReHome
Whatever HomeKit Bridge shares reaches Apple Home as normal HomeKit accessories behind your Home Assistant bridge, so ReReHome shows and controls them like any other.
Bridges get their own settings page listing the accessories behind them.
Sources
- Documentation: https://github.com/grimmpp/home-assistant-eltako
- Source code: https://github.com/grimmpp/home-assistant-eltako
- Issues: https://github.com/grimmpp/home-assistant-eltako/issues
- HACS: https://hacs.xyz
